Buy Cheap Jasper 200J Model 200 Circle Cutting Jig for Plunge Router From Here Now!
If you’re a speaker builder, then you need this tool! Introducing the Jasper Audio Circle Jig precision router attachments. These jigs convert your plunge router into a precision circle cutting device. The Model 200 will cut circles and mortises in 1/16" increments from 2-1/4" to 18-3/16" in diameter. Model 400 is perfect for tweeters and small midranges, cutting holes from 1" to 7-1/2". This makes it the ideal tool for creating highly accurate cutouts in custom built speaker cabinet baffles. Designed for use with MDF, plywood, particle board, solid woods and plastic sheet. Mounts directly to the base of 19 different models of plunge routers including Bosch 1613 and 1615, DeWalt 621 and 625, Freud FT2000E, Hitachi M8V, TR12 and M12V, Porter Cable 690 series and 7539, Skill 1823 and 1835, and all Sears, Ryobi and Makita models. Made in the U.S.A.
Readmore
Technical Details
- Circle cutting jig is great for making speaker cutouts- Cuts 256 different circles from 2-1/4 to 18-3/16-inches in diameter
- Precision-drilled pivot holes keep pins in selected holes
- Easily read scale is calibrated for a 1/4-inch router bit
- Mounts directly to the base of 19 different models of plunge routers
See more technical details
By Audiophile on a Budget (San Diego, CA)
If you need perfect circles, this thing works. It's well constructed (very thick plexiglass) and came with all the pieces to mount it to a variety of diff plunge bases. If you don't need to cut big circles, consider using the smaller jasper jig instead. I had some relatively small work-pieces and when I was cutting the circles it was a bit annoying to have to move clamps around to account for the jig requiring about 12" of clearance from the center of the cut in order to swing the full 360 degrees around to cut the circle.
By Donald Soares
Great jig, only weakness is that its made of plastic. I give it 4 stars .
By Renigami
I own a 2 1/4 HP Triton router and the best router in my opinion does not work right away with the best pre-holed circle jig. Mainly it is the mounting hole compatability.
I have to tap out three holes (my router has four holes for mounting different baseplates). Reason for this, no matter how I turn and rotate the plate on my base-less router, I can only see myself putting three holes unless I give up some circle points. The router is for the most part going to be in a position where the baseplate isn't a support anyways, but it is indeed a detail to consider.
It also helps that I already purchased and used another good product to pair with my router, the Veritas base plate for router table ability. I took out the alignment sheet for my router's holes and before I even took the circle jig out of the package (since the center is already marked and there), and poked marked holes to where I will be drilling.
Now for the other caveat. holes that are ranging below 7 inches or so in diameter... I have to do the whole peak under the baseplate to get the pivot pin into the correct hole. I have to use the duct tape method in covering up not needed holes so only the right one shows. It is a bit frustrating to get those small holes in an otherwise good jig but that's how it goes with any router I think. Mine just cuts off at 7 inches before I resort to that.
If one wants perfect, normal to the surface, holes without the messiness and uncleanliness of those regular hole saws, and to be able to do so at a certain steps of sizes, I would recommend this item but check your router first.
By Jerry Anderson (Yankton, SD)
Not much more that I can add to the other reviews here! This is a great router attachment for routing out recessed areas and holes for speaker builds or anything else that you can think of. It is accurate and attaches easily to router models it is intended for! I also have the Jasper 400T Model 400 for smaller holes as well and it is just as accurate as its bigger cousin. If your routing holes under 2" the Model 400 is required as the 200 won't go down that far! Nice Products For Sure! Purchased from Amazon with two day delivery and nice packaging. THANKS AMAZON!!!!
By phoenix3816
Simply put, this circle jig is the best I have yet used. No more measuring off the distance on your router, all the measurements are done for you! I used this jig with a Skil 1825 and it bolted right up to the base (for the most part). My only complaint on mounting is that the provided screws were to long with the factory base plate removed so I had to find others. However since my router is not officially listed as compatible it is really no fault of the product.
All my holes come out with precision and neatness, and this tool is very useful for making flushed in speaker baffles. On that note though, is where it loses one star for me. This jig will not cut a hole large enough to flush in a typical 18 inch driver. In terms of versatility, making the jig cut at least a 19 inch hole would have been better. Again, not a huge deal, but it does create inconvenience when working with 18 inch drivers.
Images Product
Buy Jasper 200J Model 200 Circle Cutting Jig for Plunge Router Now
Buy Jasper 200J Model 200 Circle Cutting Jig for Plunge Router |
Cheap Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Low Price Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Best Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Order Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Good Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Lowest Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Save Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Discount Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Purchase Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Shop Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Buying Jasper 200J Model 200 Circle Cutting Jig for Plunge Router | Where Jasper 200J Model 200 Circle Cutting Jig for Plunge Router
0 comments:
Post a Comment